Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - nodwalker

Pages: [1]
1
BitShares PTS / Re: PTS CUDA GPU Miner PtsGPUz Windows binary version v0.3c (GTX 660 Ti ~880cpm)
« on: January 24, 2014, 02:47:26 am »
Quote from: nodwalker on January 22, 2014, 07:56:25 am
abc123  Can you modify the miner to auto restart when it’s display cudaMemcpy failed, before this ploblem is solved?
it's ASUS ENGTX580 DCII/2DIS/1536MD5        1.5G
dirver vision 332.21
WIN7    X64 whith sp1
PtsGPUz0.3c has been tested on ASUS ENGTX580 DCII/2DIS/1536MD5 1.5G, dirver vision 331.82, Win7 x64 SP1 for hours. No cudaMemcpy failed occor.
The performance is ~1125 collisions/min. Have you overclocked your card? Does the power supplier powerful enough? Does the temperature of GPU core in normal range?
[/quote]
Thanks for your test
My driver vision is 332.21 WHQL but use it's GeForce Experience found another 332.21 WHQL update
I tried to update the driver. then it was working 10+ hours normal.   I’ll  keep watching
The performance is ~1235 CPM，and I never overclock



2
BitShares PTS / Re: PTS CUDA GPU Miner PtsGPUz Windows binary version v0.3c (GTX 660 Ti ~880cpm)
« on: January 22, 2014, 07:56:25 am »
Quote from: abc123 on January 22, 2014, 06:11:41 am
Quote from: oddworld on January 22, 2014, 02:21:37 am
abc123, below is the output for mining on the m2090. Normally I run without the "-t" and "-d" flag, but I have another nvidia GPU so I wanted to isolate the tesla card. Is there anything I can do to help diagnose the m2090 speed?
Thank you again.

Quote from: nodwalker on January 22, 2014, 03:36:52 am
abc123  Can you modify the miner to auto restart when it’s display cudaMemcpy failed, before this ploblem is solved?
What version of GTX 580 do you use? Video memory size?
it's ASUS ENGTX580 DCII/2DIS/1536MD5        1.5G
dirver vision 332.21
WIN7    X64 whith sp1

3
BitShares PTS / Re: PTS CUDA GPU Miner PtsGPUz Windows binary version v0.3c (GTX 660 Ti ~880cpm)
« on: January 22, 2014, 03:36:52 am »
Quote from: abc123 on January 21, 2014, 05:34:02 pm
Quote from: oddworld on January 21, 2014, 05:10:54 pm
I have two tesla m2090 and both of them do about 600 or 650 CPM. So the hardware isn't bad or anything.
Is there anything I can do to help diagnose the issue?
Thank you. It could be my miner's fault. I am considering to buy a 3GB version of GTX 580 to see why cudaMemcpy failed.
Is it runs at 600 to 650 CPM initially, or only after cudaMemcpy failed?
abc123  Can you modify the miner to auto restart when it’s display cudaMemcpy failed, before this ploblem is solved?

4
BitShares PTS / Re: PTS CUDA GPU Miner PtsGPUz Windows binary version v0.3b (GTX 480 ~1030cpm)
« on: January 19, 2014, 05:42:31 am »
Quote from: sand02 on January 19, 2014, 03:08:46 am
Been using this 0.3b for about one day. I've some problems. At first the speed was 1600CPM but this morning i found the speed was reduced to 800CPM.

My hardware is GTX780Ti

P.S This soft is very nice
I have the same problem  ，because of Cudamemcpy failed
My hardware is GTX580  At first the speed was 1200CPM

Pages: [1]

Page created in 0.199 seconds with 24 queries.