Continuous work day, and displays the results as follows:

Balance: 0.072987

Unconfirmed: 10.731204

When can pay to my wallet?

http://mmc.xpool.xram.co/faq

When do I get paid?

Payments are made when the confirmed balance is above 0.5 MMC

I hope this helps

Mike

Happy New Year Kabayan 

Mike

Quote from: n00b2013 on December 31, 2013, 12:34:54 am

long now .. something is def up

yes, you are right. Investigating again.... I will find out what the problem is now.

killerbyte, i you can also check the REJECT rate, i think its too many on my end im not sure with others.

Thanks,

Mike

Quote from: ig0tik3d on December 30, 2013, 09:43:03 am

Quote from: KillerByte on December 30, 2013, 12:41:25 am

Pool is at a low of 250 miners right now... whats going on?

))


killerbyte what you think about this ? ))


and why you don't update windows binary or new version doesn't work properly?

hey I just woke up, noticed that there were 610 miners on the pool, didnt last long though. I woke up last night finding out there was some commotion about DDoSses... did this pool get DDoSsed actually? I have no evidence it was.

Does the windows binary not work? I tested it with Wine... let me fix the website as you suggested too.

Killerbyte, maybe you can make the payouts automatically paid upon reaching your payout theeshold. This might 1 factor on why some miners didnt last long specially for new ones. In my case i was following this thread so till up to now i have 40 cores mining at your pool ...just a suggestion.


Mike

It's just hashing forever and not receiving any  new "[Master] Work received". Then after a while it will go "force reconnect".

The round shares on this block is pretty nuts btw... I don't get it.

Same here, and lots of REJECTS

Attached screenshot, 10 instance of 2CPUs

http://gigamike.net/mmc-mining.png

This is may 3rd creation of instance coz 3 hours ago pool was down (system:111).

Mike

yes down , system:111

Mike

Quote from: gigamike on December 25, 2013, 07:40:35 am

Guys,

question, i have a server which has only 2 CPUs. But i can run -genproclimit=20. If i set like that does it has advantage or just same as running -genproclimit=2?

Thanks in advance,

Mike

most of the time it just causes a slowdown a believe, that is my experience with XPM. If you have an intel processor with hyperthreading though, make sure to use all the cores.

thankyou for your fast reply killerbyte,

Can you help me the best -genproclimit=?? set

below is my server CPUs

root@MMC3-8:~/memoryminer/src# cat /proc/cpuinfo
processor       : 0
vendor_id       : GenuineIntel
cpu family      : 6
model           : 2
model name      : QEMU Virtual CPU version 1.0
stepping        : 3
microcode       : 0x1
cpu MHz         : 1999.999
cache size      : 4096 KB
fpu             : yes
fpu_exception   : yes
cpuid level     : 4
wp              : yes
flags           : fpu de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pse36 clflush mmx fxsr sse sse2 syscall nx lm rep_good nopl pni vmx cx16 popcnt hypervisor lahf_lm
bogomips        : 3999.99
clflush size    : 64
cache_alignment : 64
address sizes   : 40 bits physical, 48 bits virtual
power management:

processor       : 1
vendor_id       : GenuineIntel
cpu family      : 6
model           : 2
model name      : QEMU Virtual CPU version 1.0
stepping        : 3
microcode       : 0x1
cpu MHz         : 1999.999
cache size      : 4096 KB
fpu             : yes
fpu_exception   : yes
cpuid level     : 4
wp              : yes
flags           : fpu de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pse36 clflush mmx fxsr sse sse2 syscall nx lm rep_good nopl pni vmx cx16 popcnt hypervisor lahf_lm
bogomips        : 3999.99
clflush size    : 64
cache_alignment : 64
address sizes   : 40 bits physical, 48 bits virtual

Thanks again,

Mike